sae 100r4 hose outer dia size

3/4"ID x 150'' MSHA Accepted SAE 100R4 300psi Hydraulic

sae 100r4 Inner Tube: Nitrile Blend Reinforcement: 3/4" - 1-1/2" 1 helical cabled wire and 1 fiber braid 2"- 1 helical, single-stranded wire and 1 fiber braid Cover: Neoprene Temperature Range: -40°F to +212°F (-40°C to +100°C) Hose Ends: Coll-O-Crimp® U-Series for 2-20 sizes; Coll-O-Crimp® attachable K-Series; 039 K-Series; 430 E-Series

Table of Contents - Parker Hannifin

Nuers to indie hose and fitting size. The Dash Nuer, or Dash Size, is the measure of a hose’s Inner Diameter (I.D.) in sixteenths of an inch. (The exception to this is SAE 100R5 hose. See the chart below for complete details.) This measuring system of the inside diameter of the hose is universally used by the fluid power industry today.

Dash Sizing for Hoses and Tubes Explained

Each dash size corresponds to a progressively larger diameter, measured in sixteenths of an inch. “-1” is 1/16, “-2” is 2/16, and so on. In this case, -6 hose would indie a hose with an inside diameter of 6/16”, or 3/8". In another example, a -10 tube would indie a tube with an outside diameter of 10/16", or 5/8".

SAE Tube Fittings | McMaster-Carr

Also known as ball-seat hose nipples, these fittings consist of a barbed shaft with a rounded end that sits inside a threaded nut. When mated with a male threaded fitting, the rounded end presses tightly against the inside of the male threads for a better seal than a single-piece fitting. Once asseled, insert the barbed end into hose and secure with a clamp or a crimp-on hose ferrule.

Medium Pressure Suction and Return Line Hoses - SAE 100R4

Medium Pressure Suction and Return Line Hoses - SAE 100R4 - 811S Where To Buy Parker''s Medium Pressure No-Skive Suction and Return Line Hose 811S has been designed with an Isobaric 1.0 MPa for all sizes and a temperature range from -40°C up to +100 °C

Hydraulic Hose: SAE J517 100R3, 100R4, 100R5, 100R6

Hydraulics hose SAE J517 100R4: Size (Inch) Inside Diameter: Reinforcement: Outside Diameter: Proof Pressure: Working Pressure: Burst Pressure: Bend Radius: Basic (mm) Tolerance Plus (mm) Tolerance Minus (mm) Hydraulics hose SAE J517 100R5: Size (Inch) Inside Diameter: Reinforcement: Outside Diameter: Proof Pressure: Working Pressure: Burst

Hose HOSE - Parker Hannifin

SAE 100R4 Suction & Return Line Hose Hose Outer Diameter A critical measurement when considering hose clamps and appliions where envelope size is limited. 451TC-8 - Hose inside diameter dash size (in this case, 8/16” or 1/2”) Indies Hose Section Approved Fitting

Table of Contents - Parker Hannifin

Nuers to indie hose and fitting size. The Dash Nuer, or Dash Size, is the measure of a hose’s Inner Diameter (I.D.) in sixteenths of an inch. (The exception to this is SAE 100R5 hose. See the chart below for complete details.) This measuring system of the inside diameter of the hose is universally used by the fluid power industry today.

Hose HOSE - Parker Hannifin

SAE 100R4 Suction & Return Line Hose Dry Air/Hot Water Multipurpose Multipurpose High Temperature Air Brake Hose Hose Outer Diameter A critical measurement when considering hose clamps and 451TC-8 - Hose inside diameter dash size (in this case, 8/16” or 1/2”) Indies Hose Section For more

SAE 100R4 - Hydraulic Hose & Fittings - JGB Featured Markets

JGB Featured Markets - SAE 100R4 - Hydraulic Hose & Fittings. JGB Enterprises, Inc. is a hose asseler of hydraulic and industrial hoses and hose asselies for all appliions. We assele a full line of specialized hoses and fittings, including hydraulic hose, water hose, flexible hose, special appliion hose, and braided hose. JGB Enterprises has long standing relationships with over

SAE 100R6 Low Pressure Hydraulic Hose for High Temp

SAE 100R6 Hydraulic Hose for tight routing purposes. SAE 100R6 textile braided hydraulic hose does great job in low pressure conditions, especially where tight routing is urgently required. Black nitrile tube is quite compatible with petroleum base hydraulic fluids with temperature range from -40 to 100°C.

Making Sense of Hydraulic Hose Standards | Hydraulics

For example, Parker Hannifin’s Hose Products Division offers hydraulic hoses with one-half the minimum bend radius outlined in SAE standards at full SAE pressure. For example, the bend radius of Parker’s 797 hydraulic hose is half of SAE’s 100R1, 100R2, 100R4, 100R12, and 100R13 minimum requirement, which reduces hose length requirements

Hydraulic Hose Selection Guide

Hydraulic Hose Selection Guide NRP Page Nuers Dash Size and W orking Pressure SAE 100R4 2004 Suction & Return Line 9 20-37 300 250 200 150 100 62 thru 1/2 and two wire high tensile steel braid in sizes 5/8 thru 1. Cover: Black, oil and abrasion resistant Neoprene (CR).

1"ID x 150'' MSHA Accepted SAE 100R4 250psi Hydraulic Hose

sae 100r4 Inner Tube: Nitrile Blend Reinforcement: 3/4" - 1-1/2" 1 helical cabled wire and 1 fiber braid 2"- 1 helical, single-stranded wire and 1 fiber braid Cover: Neoprene Temperature Range: -40°F to +212°F (-40°C to +100°C) Hose Ends: Coll-O-Crimp® U-Series for 2-20 sizes; Coll-O-Crimp® attachable K-Series; 039 K-Series; 430 E-Series

Hydraulic hose - SAE standards | Hydraulics & Pneumatics

SAE 100R4 hose should be used in low pressure and vacuum appliions, with petroleum- and water-based hydraulic fluids, within a temperature range from140° to 100° C. It is constructed with an inner tube of oil-resistant synthetic rubber, a reinforcement consisting of a ply, or plies, of woven or braided textile fibers with a suitable spiral

GMV Global MegaVac® Return Line and Suction Hose - SAE 100R4

GMV Global MegaVac® Return Line and Suction Hose - SAE 100R4. Recommended for petroleum and water based hydraulic fluids in suction lines or in low pressure return lines. Meets or exceeds requirements of SAE 100R4. Recommended Couplings: GL Couplings, GlobalSpiral™ Plus Couplings, MegaCrimp® Couplings (-12 through -20).

Hydraulic Hose: SAE J517 100R3, 100R4, 100R5, 100R6

Hydraulics hose SAE J517 100R4: Size (Inch) Inside Diameter: Reinforcement: Outside Diameter: Proof Pressure: Working Pressure: Burst Pressure: Bend Radius: Basic (mm) Tolerance Plus (mm) Tolerance Minus (mm) Hydraulics hose SAE J517 100R5: Size (Inch) Inside Diameter: Reinforcement: Outside Diameter: Proof Pressure: Working Pressure: Burst

GOODYEAR HYDRAULIC HOSE PART NUER DESIGNATIONS

GR4 SAE 100R4 GR5 SAE 100R5 GR6 SAE 100R6/EN 854 R6 HR6 DESERT SAE 100R6/EN 854 R6 (High Temp) GR7 SAE 100R7/EN 855 R7 HJ = Jack Hose Hose DASH SIZE (Hose Inside Diameter) Last 2 characters of Part Nuer after hyphen All hoses except R5 02 = 1/8" (3.3 mm) 3 = 3/16" (4.8 mm) 4 = 1/4" (6.4 mm)

R4-32-CL100 | 2" SAE 100R4 Suction Hose (100 feet

2" SAE 100R4 Suction and Return Hose is recommended for low pressure or vacuum lines in hydraulic system service with petroleum and water-base fluids. Interchanges with Aeroquip FC318-32, Gates 32G4, Parker 881-32, and Weatherhead H03932

Hydraulic Hose Selection Guide

Hydraulic Hose Selection Guide NRP Page Nuers Dash Size and W orking Pressure SAE 100R4 2004 Suction & Return Line 9 20-37 300 250 200 150 100 62 thru 1/2 and two wire high tensile steel braid in sizes 5/8 thru 1. Cover: Black, oil and abrasion resistant Neoprene (CR).

Dash Sizing for Hoses and Tubes Explained

Each dash size corresponds to a progressively larger diameter, measured in sixteenths of an inch. “-1” is 1/16, “-2” is 2/16, and so on. In this case, -6 hose would indie a hose with an inside diameter of 6/16”, or 3/8". In another example, a -10 tube would indie a tube with an outside diameter of 10/16", or 5/8".

Crimp-Style Hose and Fittings - Parker Hannifin

Capability . . . through 2" SAE 100R1, 100R2,. 100R3, 100R4, 100R5, 100R6, 100R7, 100R8, outer covers to meet specific pressure, temperature and other performance requirements. Reference shapes and sizes to meet all your hose connector needs. Smooth-bore FEP core tube with helical

FC619-16 | Eaton PowerSource

SAE 100R4 ABS: Burst Pressure (bar) 70: Burst Pressure (psi) 1000: Description: Flexible 1/2 SAE bend Wire inserted suction: Family: Hose: General Appliion: Suction and transfer appliions for petroleum hydraulic fluids, fuel, lubriing oils, gasoline,water and many other industrial fluids. Hose Base Nuer: FC619: Inside Diameter (in) 1

sae 100r4 e s rubber hose - monetatraforata

SAE 100R2T*1′′ Standard SAE Diameter 25mm Size 1inch Main Products: Rubber Hose, Hydraulic Hose, High Pressure Rubber Hose, Oil. 20171017-Key words: hydraulic hoses, rubber hoses, industrial hoses, braid hoses,compact hose, SAE 100R4 Suction Hose, EN 854 1TE Low Pressure Hos.

1-1/2"ID x 100'' MSHA Accepted SAE 100R4 150psi Hydraulic

sae 100r4 Inner Tube: Nitrile Blend Reinforcement: 3/4" - 1-1/2" 1 helical cabled wire and 1 fiber braid 2"- 1 helical, single-stranded wire and 1 fiber braid Cover: Neoprene Temperature Range: -40°F to +212°F (-40°C to +100°C) Hose Ends: Coll-O-Crimp® U-Series for 2-20 sizes; Coll-O-Crimp® attachable K-Series; 039 K-Series; 430 E-Series